Posts Tagged Pi

How to run Raspberry Pi from a USB hard drive

Raspberry Pi - USB Hard drive

I had been using my Raspberry Pi with a 4 GB – class 4  SD card Kingston until it decided to die (since I burn the image the first time that SD card was a little problematic). Because I didn’t have another 2GB or higher SD card, I decided to do a research to check if I could use the first partition as boot and another partition from an external USB hard drive of 320 GB. Effectively it can be done and I describe the needed steps on this article.

Raspbian Image

I decided to use the Raspbian image Raspbian 2013-02-09-wheezy-raspbian.img, but first I had to do a trick: dump the image to a 8 GB pen drive to be able separate the /boot partition and the remaining file system.

Dumping Raspbian to the pen drive

Just dump the Raspbian image as it were a SD card, but instead of  using /dev/mmcblk0 do it on your  pen drive:

# dd bs=4M if=/home/lgallard/Projects/RaspberryPi/2013-02-09-wheezy-raspbian.img of=/dev/sdb

Extracting the boot image

In order to extract the Raspbian’s boot image just dump the first partition of the pen drive:

# dd if=/dev/scb1 of=/home/lgallard/Projects/RaspberryPi/2013-02-09-wheezy-raspbian.boot.img

Extracting the operating system

Do the same to extract the file system where the operating systems resides:

# dd if=/dev/sdc2 of=/home/lgallard/Projects/RaspberryPi/2013-02-09-wheezy-raspbian.fsext4.img

Partition /boot on SD card

You will still need a SD card to boot your Rasberry, but it not longer need to be 2GB, in fact it could be much less, even 64 MB (I use a 1 GB SD card I found). To do so, you need to make a partition with GParted of about 60 MB as show in the next picture:

GParted - SD Card

Now copy the content of the first image you dumped previously:

# dd if=/home/lgallard/Projects/RaspberryPi/2013-02-09-wheezy-raspbian.boot.img of=/dev/sdb1

Once you have copied the data you must mount that partition and then edit file /media/usb0/cmdline.txt  (change /media/usb0 according to the mounting point), and put the following:

dwc_otg.lpm_enable=0 console=ttyAMA0,115200 kgdboc=ttyAMA0,115200 console=tty1 root=/dev/sda1 rootfstype=ext4 elevator=deadline rootwait

Here is important to put root=/dev/sda1  so the Raspberry uses the first partition of the external USB hard drive as the root partition, I mean, the “/” directory at boot.

Partitioning the external USB hard drive

Connect the hard drive to a PC and make the partitions as shown in the next picture. The first partition will content the file system  and the second one will be used for saving data (you can define later that in the /etc/fstab of your the RaspBerry Pi).

GParted - hard drive

File system partition “/”

Now you can dump the Raspian image you got to the first partition of the USB hard drive. To do so type this:

# dd if=/home/lgallard/Projects/RaspberryPi/2013-02-09-wheezy-raspbian.fsext4.img of=/dev/sdc1

Fixing the size partition

As you can see in the last picture, the partition was created of 9 GB size, but if you mount the partition it will report it as only 2 GB because the Raspian image has that size by default.  To fix this you must umount the partiton and and resize the file system:

# umount /dev/sdc1
# e2fsck -f /dev/sdc1
e2fsck 1.42.5 (29-Jul-2012)
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
Raspbian: 66488/114688 files (0.1% non-contiguous), 346538/458240 blocks
# resize2fs /dev/sdc1
resize2fs 1.42.5 (29-Jul-2012)
Resizing the filesystem on /dev/sdc1 to 2304000 (4k) blocks.
The filesystem on /dev/sdc1 is now 2304000 blocks long.

After that check the available space. It should report something like this:

# df -h
/dev/sdc2 285G 191M 271G 1% /media/Data
/dev/sdc1 8.7G 1.3G 7.0G 16% /media/Raspbian

If you follow these steps, your Rasberry Pi will boot from a USB hard drive.

Final notes

  • It’s a fact that a hard drive have a higher price than a SD card but you have to consider the later will suffer more, specially a file system with journal can kill the SD card, so it’s not crazy to think in an external USB hard drive.
  • This hard drive and keyword are powered by the Rasberry Pi without problems. But if I connect something more, for instance a mouse, it can’t handle all and the device reboots.
  • Using a hard drive can solve the SD card compatibility issue (recommended class 6 type). In my case I used a Sandsik of 1 GB, class 4 and it worked perfectly.
  • Probably you can use dd and extract the /boot and file system partitions, but due I didn’t know the exact size and because I was a little lazy a decide to dump the Rasbian image on a pen drive and extract the images that way.

, , , ,

14 Comments

Unboxing the Raspberry Pi

Raspberry board

My Raspberry Pi has arrived…and sooner than expected (they say in three weeks). I would say it just took one week to ship it to Venezuela. In my case I bought it at RS Raspberry Pi Store and the shipment was direct to Venezuela. And yes, IPOSTEL shipments do arrive.

Unboxing

Here  I leave some picture of the unboxing…

Raspberry Delivery Raspberry box

Unboxing the Raspberry Raspberry Quick Start

Raspberry Case AC adaptors
American AC wire

I just need a SD card, which must be class 4…at the moment I continue experimenting with the QEMU image as I mentioned in my last post.

, ,

10 Comments